hi, I got this error fatal error c000021a and when I sear h the net I found that it was a problem from security settings but I did not any real fix for this error Please advise , dump file attached here: http://www23.zippyshare.com/v/79547066/file.html thanks

Bug Check 0xC000021A: STATUS_SYSTEM_PROCESS_TERMINATED Cause This error occurs when a user-mode subsystem, such as WinLogon or the Client Server Run-Time Subsystem (CSRSS), has been fatally compromised and security can no longer be guaranteed. In response, the operating system switches to kernel mode. Microsoft Windows cannot run without WinLogon or CSRSS. Therefore, this is one of the few cases where the failure of a user-mode service can shut down the system. Mismatched system files can also cause this error. This can occur if you have restored your hard disk from a backup. Some backup programs might skip restoring system files that they determine are in use. Resolution: Resolving an error in a user-mode device driver, system service, or third-party application: Because bug check 0xC000021A occurs in a user-mode process, the most common culprits are third-party applications. If the error occurred after the installation of a new or updated device driver, system service, or third-party application, the new software should be removed or disabled. Contact the manufacturer of the software about a possible update. If the error occurs during system startup, restart your computer, and press F8 at the character-based menu that displays the operating system choices. At the resulting Windows Advanced Options menu, choose the Last Known Good Configuration option. This option is most effective when only one driver or service is added at a time. If this does not resolve the error, try manually removing the offending software. If the system partition is formatted with file allocation table (FAT), use an MS-DOS startup disk to gain access to the computer's hard disk. If the system partition is formatted with NTFS file system, you might be able to use Safe Mode to rename or delete the faulty software. If the faulty software is used as part of the system startup process in Safe Mode, you need to start the computer using the Recovery Console in order to access the file. If a newly installed piece if hardware is suspected, remove it to see if this resolves the issue. Try running the Emergency Recovery Disk (ERD) and allow the system to repair any errors that it detects. Resolving a mismatched system file problem: If you have recently restored your hard disk from a backup, check if there is an updated version of the Backup/Restore program available from the manufacturer. Make sure the latest Windows Service Pack is installed. http://msdn.microsoft.com/en-us/library/ff560177%28VS.85%29.aspx"A programmer is just a tool which converts caffeine into code" CLIP- Stellvertreter http://www.winvistaside.de/

Hi, After checking the dump file, I found the error code C000021A was caused by the ntkrnlmp.exe. As Ntoskrnl.exe is a kernel component of Microsoft OS, it should be something caused a Ntoskrnl.exe failure when running smss.exe and Ntoskrnl.exe failure which caused the BSOD error. At this time, I suggest go to test this issue in Safe Mode, Clean Boot and Device Clean Boot to determine the possible cause. Device Clean Boot ================= 1. Click Start, type "devmgmt.msc" (without quotation marks) in the Search bar and press Enter. 2. Expand "Sound, video and game controllers". 3. Right click on your sound card and then click "Properties. 4. In the dropdown menu of Device Usage, please choose "Do not use this device (disable)" and click OK. 5. Please use the same method to disable other dubious hardware such as: internal modem, network card and CD-R drive. Please note some devices such as video adapter are not available to be disabled. · If the issue persists, would you please upload more minidump files for further research? Collect Minidump Files ================= 1. Click "Start", input "SYSDM.CPL" (without quotation marks) in the “Search” bar and press “Enter”. 2. Switch to the "Advanced" tab and click the "Settings" button under "Startup and Recovery". 3. Under "Write debugging information" section, make sure the "Small memory dump (128KB)" option is selected. 4. Make sure "%SystemRoot%\Minidump" is in the "Small dump directory" open box and click “OK”. If the Blue Screen appears again, please refer to the following steps to collect memory dump files: 1. Click “Start”, type “%SystemRoot%\Minidump" (without quotation marks) in “Search” bar and press “Enter”. 2. Go to your Desktop, right-click on it and create a new folder named "Dump". 3. Copy all the memory dump files (looks like [Mini092008-01.dmp]) in Minidump to this folder. 4. Right-click on the Dump folder, click "Send To", and click "Compressed (zipped) Folder". 5. Please send the ZIP file to us. You can refer to the following link to upload the information: http://social.technet.microsoft.com/Forums/en-US/w7itproui/thread/4fc10639-02db-4665-993a-08d865088d65 You may also analyze them with Debugging Tools by yourself. You can install it and it’s Symbol Packages from the following link: http://www.microsoft.com/whdc/Devtools/Debugging/default.mspx WinDbg will tell you the possible cause. For more information, please read Microsoft KB Article: How to read the small memory dump files that Windows creates for debugging. If no clue can be found, you may contact Microsoft Customer Service and Support (CSS) via telephone so that a dedicated Support Professional can assist with your request. To troubleshoot this kind of kernel crash issue, we need to debug the crashed system dump. Unfortunately, debugging is beyond what we can do in the forum. Please be advised that contacting phone support will be a charged call. To obtain the phone numbers for specific technology request please take a look at the web site listed below: http://support.microsoft.com/default.aspx?scid=fh;EN-US;OfferProPhone#faq607 Regards, Sabrina