Can anyone give advice on getting dual NICs working at the same time? I have managed to do it in the past on other machines. Now, when the NIC2 is enabled and connected, you can no longer ping NIC1 from another machine. NIC1 stops working almost as soon as you connect NIC2 to something. (You can connect it to anything - a firewall appliance with a configured IP address or a cheap unmanaged switch with nothing else connected to it.) NIC1 resumes working normally The machine is running Windows Server 2008 x64 (not R2). I installed the latest network drivers in case that was the problem. When I connect the cable and things stop working, this event is generated: Log Name: System Source: Microsoft-Windows-ResourcePublication Date: 2011/09/21 4:14:59 PM Event ID: 102 Task Category: None Level: Information Keywords: Event originating from the fdrespub service User: LOCAL SERVICE Computer: SERVER6.mynetwork.com Description: The service temporarily stopped publishing because of a power event. When I disconnect the cable and things return to normal, event 104 similar to event 102 says, "The service is publishing to the network." Bizarre, isn't it? I hope you can help me resolve this.

If you want to use two network cards as a load balancing or redundancy you can team them using vendor software or you can bridge the network interfaces. http://support.microsoft.com/kb/309640 Darshana Jayathilake

Hi, Thanks for posting here. So are both NICs holding the IP addresses from same IP segment ? could you first please post the “ipconfig /all” results from this host here ? Usually , we will mix NICs by using Teaming , however this should be supported by NIC factory . Here are some article for reference: Expected Behavior of Multiple Adapters on Same Network http://support.microsoft.com/kb/175767/en-us Using the multiple NICs of your File Server running Windows Server 2008 (and 2008 R2) http://blogs.technet.com/b/josebda/archive/2010/09/03/using-the-multiple-nics-of-your-file-server-running-windows-server-2008-and-2008-r2.aspx Thanks. Tiger Li Please remember to click Mark as Answer on the post that helps you, and to click Unmark as Answer if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Strange... So, just to clarify, does the NIC1 become disabled or is it remain enabled with the link lgiht lit? Are you not able to ping it by IP, or just by name? pls clarify...Visit anITKB.com, an IT Knowledge Base.

No, NIC1 does not appear disabled. In the "Network Connections" window, the status of NIC1 does not change. The light on the physical NIC remains lit. The machine can successfully ping out from it. Other machines fail to ping by IP or by name. Cam

byIP...If you can PING "out" but cannot Ping "in", that would lead me to beleive that there is some filtering going on between the hosts. Whether you can PING in or out, there is a two way communication that is occuring. If you can PING out, the ICMP messages are reaching the destination and making their way back to the server. If you cannot PING in, where does it stop? Try a tracert from one of your hosts to this server. Where does the packet stop? Also, take a look at the routing table on this multihomed system. Open a command prompt and type ROUTE PRINT. review the routes. Anything look strange? Also, I assume that the 10.1.1.x network does not exist anywhere else on your network. Focus on IP communication at the moment, don't worry about name resolution or any other higher level protocols. Visit anITKB.com, an IT Knowledge Base.

Hi Cam, Thanks for update. I agree , please post the route table form this server here. It seems like a source address choosing issue . I suspect that we may need modify the route entries on that server in order to make the connectivity up . Here are some article for reference: Multiple IP Addresses on a Single NIC http://support.microsoft.com/kb/149399 Source IP address selection on a Multi-Homed Windows Computer http://blogs.technet.com/b/networking/archive/2009/04/24/source-ip-address-selection-on-a-multi-homed-windows-computer.aspx Thanks. Tiger Li Please remember to click Mark as Answer on the post that helps you, and to click Unmark as Answer if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.