Best practice to add the role of PXE Point in SCCM
Hello good I would like to know how
to follow few steps to properly install a
SCCM PXE Point role, when
you install WDS it has this
set or not set the wds is recommended
and then install the SCCM PXE
role.
It should configure the DHCP
option 60 if not on the same machine
and also listen on port
67.
Is there any official document from Microsoft.
Thanks and regards,
May 26th, 2012 6:37am
Here's the official documention for installing the PSP:
http://technet.microsoft.com/en-us/library/bb680668.aspx
You should *not* configure WDS manually, the PSP will take care of this.
Using DHCP scope is generally discouraged and is *not* supported by Microsoft. If you need to PXE boot across broadcast boundaries, then you should use iphelpers.Jason | http://blog.configmgrftw.com | Twitter @JasonSandys
Free Windows Admin Tool Kit Click here and download it now
May 26th, 2012 11:49am
Here's the official documention for installing the PSP:
http://technet.microsoft.com/en-us/library/bb680668.aspx
You should *not* configure WDS manually, the PSP will take care of this.
Using DHCP scope is generally discouraged and is *not* supported by Microsoft. If you need to PXE boot across broadcast boundaries, then you should use iphelpers.Jason | http://blog.configmgrftw.com | Twitter @JasonSandys
May 26th, 2012 11:50am
Hi,
In addition, you can read this technet blog about WDS and PXE service point troubleshooting. Inside the blog, not only troubleshooting tips but also step-by-step configure WDS and PXE service point are referenced.
http://blogs.technet.com/b/system_center_configuration_manager_operating_system_deployment_support_blog/archive/2011/10/14/troubleshooting-the-pxe-service-point-and-wds-in-configuration-manager-2007.aspx
Please reference the following parts of the blog post:
Co-hosting DHCP and WDS On The Same Server
How To Properly Install And Set Up A New Instance Of WDS And A PXE Service Point
Hope this will help.
Thanks
Free Windows Admin Tool Kit Click here and download it now
May 28th, 2012 4:11am
Hi,
In addition, you can read this technet blog about WDS and PXE service point troubleshooting. Inside the blog, not only troubleshooting tips but also step-by-step configure WDS and PXE service point are referenced.
http://blogs.technet.com/b/system_center_configuration_manager_operating_system_deployment_support_blog/archive/2011/10/14/troubleshooting-the-pxe-service-point-and-wds-in-configuration-manager-2007.aspx
Please reference the following parts of the blog post:
Co-hosting DHCP and WDS On The Same Server
How To Properly Install And Set Up A New Instance Of WDS And A PXE Service Point
Hope this will help.
Thanks
May 28th, 2012 4:12am
I used to swear by Option 66 and 67 but after running across one very obscure set of circumstances where it wouldn't work, I now swear by IPHelpers.
So...
Get someone in networking to setup your IPHelpers on the appropriate VLANs. Install WDS. Do not touch it or initialize it. Reboot. If you want to install R2, do it now. Enable Unknown Computer support soonest if you plan to use it.
Install the PXE Service Point. Watch the PXESetup.log + the MSI log for any errors. Reboot once the install logs show everything is good.
Push both x86 and x64 boot images to the PXE distribution point (server share). Once that's come down, verify the SMSBoot\x86 and \x64 directories have all the network boot files. WDSNBP.com is one of them. (If the SMSBoot directories won't populate, check
the SMSPXE.log for issues. If on 2008, you can have a problem with the c:\windows\temp\pxebootfiles directory and may need to delete it and restart WDS).
Once you've got the network boot files in the X86/X64 directories, setup a non-mandatory advertisement and run a test. (Be careful as to the scope of that test, obviously) The PXEControl.log and SMSPXE.log are the most salient logs here.
One point to remember - if you aren't getting requests from MAC addresses aside from the self-tests, the problem is usually on the network side. I've been on too many bridge calls blaming the PXE Service Point, only to find the IPHelper wasn't configured
properly.
If you absolutely HAVE to use DHCP scope options, set option 66 to the hostname or IP address of the server, then option 67 as the bootfile path. Don't use Option 60 - I've never seen that work or be helpful in anyway.
My two cents....
Free Windows Admin Tool Kit Click here and download it now
May 29th, 2012 1:52pm